User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            Genisco GF-4150-2 Capacitor
INSTRUMENT:            Solar 7113-106R Capacitor
DATE:                  23-Nov-97
AUTHOR:                User Contributed
REVISION:              0
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       5
NUMBER OF LINES:       67
STANDARD:              esi 273
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-                        P                            F
  1.002  ASK+                                          X
  1.003  HEAD         * INITIAL CONDITIONS *
  1.004  DISP         The following Standard test equipment is required:
  1.004  DISP         esi 273 Capacitance Bridge
  1.005  JMPT         1.008          Solar 7113-106R Capacitor
  1.006  DISP         Set the esi 273 front panel controls as follows:
  1.006  DISP         POWER ON/OFF ...................................... ON
  1.006  DISP         FREQUENCY kHz .................................. 0.120
  1.006  DISP         GEN LEVEL ................................... fully cw
  1.006  DISP         DISIPATION FACTOR dials .................... 0.001 x 0
  1.006  DISP         C RANGE .......................................... 1µF
  1.006  DISP         CAPACITANCE dials .............................. 9.999
  1.006  DISP         LOG/LIN switch ................................... LOG
  1.007  JMP          1.009
  1.008  DISP         Set the esi 273 front panel controls as follows:
  1.008  DISP         POWER ON/OFF ...................................... ON
  1.008  DISP         FREQUENCY kHz .................................. 0.120
  1.008  DISP         GEN LEVEL ................................... fully cw
  1.008  DISP         DISIPATION FACTOR dials .................... 0.001 x 0
  1.008  DISP         C RANGE ......................................... 10µF
  1.008  DISP         CAPACITANCE dials .............................. 1.000
  1.008  DISP         LOG/LIN switch ................................... LOG
  1.009  DISP         Set the DETECTOR SENSITIVITY control so that line on
  1.009  DISP         knob lines up with dot at 9 o'clock.
  1.010  PIC          esi
  1.011  DISP         Adjust CAPACITANCE and DISSIPATION FACTOR dials
  1.011  DISP         alternately for a null on the meter.
  1.012  DISP         Set the DETECTOR SENSITIVITY control fully cw.
  1.013  DISP         Adjust CAPACITANCE and DISSIPATION FACTOR dials
  1.013  DISP         alternately for a null on the meter.
  1.014  HEAD         {* CAPACITANCE TEST *}
  1.015  JMP          2.001
  1.016  EVAL
  2.001  STD          esi 273
  2.002  MEMI         Use keyboard to enter 273 reading in µf:
  2.003  ACC          10.000µf       0.1% 0.001U
  2.004  MEME
  2.005  MEMC         µf             1.000U
#!          Test Tol 1, Sys Tol 0.011, TUR 90.9091 (>= 4.00).
  3.001  HEAD         {* DISSIPATION FACTOR TEST *}
  3.002  JMP          4.001
  3.003  EVAL
  4.001  MEMI         Use keyboard to enter 273 Dissipation Factor (red scale)
  4.002  ACC          0.000          0.0011U +1%
  4.003  MEME
  4.004  MEMC         D.F.           +1.000U
#!          Test Tol 1, Sys Tol 0.0011, TUR 909.091 (>= 4.00).
  5.001  END
#! T.U.R.s less than 4.00:                  0
#! T.U.R.s estimated using RANGE value:     0
#! T.U.R.s not calculated (ASK- U):         0
#! T.U.R.s not computable at compile time:  0
#! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.